Server Fault Asked by Halfgaar on November 7, 2021
It shouldn’t be this hard, but I can’t figure out how to monitor the RAID status with the HPE Smart Array E208i-p SR Gen10, in a HP ProLiant DL360 Gen10 in Linux.
/proc
or /sys
.arcconf
says: Controllers found: 0
.ssacli controller all show
says: Error: No controllers detected.
Error: No controllers detected.
Edit: it was a bit confusing because this server has two RAID controllers, but neither work so far, so the question is the same.
This is the lspci -v
output of the E208i-p:
11:00.0 Serial Attached SCSI controller: Adaptec Smart Storage PQI 12G SAS/PCIe 3 (rev 01)
Subsystem: Hewlett-Packard Company Smart Array E208i-p SR Gen10
Physical Slot: 1
Flags: bus master, fast devsel, latency 0, IRQ 26, NUMA node 0
Memory at e2800000 (64-bit, non-prefetchable) [size=32K]
I/O ports at 4000 [size=256]
Capabilities: [80] Power Management version 3
Capabilities: [b0] MSI-X: Enable+ Count=64 Masked-
Capabilities: [c0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] #19
Kernel driver in use: smartpqi
Kernel modules: smartpqi
This of the P408i-a:
b1:00.0 Serial Attached SCSI controller: Adaptec Smart Storage PQI 12G SAS/PCIe 3 (rev 01)
Subsystem: Hewlett-Packard Company Smart Array P408i-a SR Gen10
Flags: bus master, fast devsel, latency 0, IRQ 32, NUMA node 0
Memory at f3800000 (64-bit, non-prefetchable) [size=32K]
I/O ports at c000 [size=256]
Capabilities: [80] Power Management version 3
Capabilities: [b0] MSI-X: Enable+ Count=64 Masked-
Capabilities: [c0] Express Endpoint, MSI 00
Capabilities: [100] Advanced Error Reporting
Capabilities: [300] #19
Kernel driver in use: smartpqi
Kernel modules: smartpqi
Linux version:
cat /etc/lsb-release
DISTRIB_ID=Ubuntu
DISTRIB_RELEASE=18.04
DISTRIB_CODENAME=bionic
DISTRIB_DESCRIPTION="Ubuntu 18.04.4 LTS"
Edit: on a slightly order server, with ‘Hewlett-Packard Company Smart Array Gen9 Controllers (rev 01) / Hewlett-Packard Company P440’, the hpssacli
tool does work.
For the Red Hat users out there: Install the HP repo (keyfiles are available on the HP repo page); then you can use your package manager to install:
[hpsum]
name=HPE Smart Update Manager
baseurl=http://downloads.linux.hpe.com/repo/hpsum/rhel/7Server/x86_64/current/
enabled=1
gpgcheck=1
gpgkey=file:///etc/pki/rpm-gpg/GPG-KEY-hpsum
[HP-mcp]
name=HP Management Component Pack for ProLiant
baseurl=http://downloads.linux.hpe.com/SDR/repo/mcp/centos/7/x86_64/current/
enabled=1
gpgcheck=1
gpgkey=file:///etc/pki/rpm-gpg/GPG-KEY-mcp
[HP-spp]
name=HP Service Pack for ProLiant
baseurl=http://downloads.linux.hpe.com/SDR/repo/spp/RHEL/7/x86_64/current/
enabled=1
gpgcheck=1
gpgkey=file:///etc/pki/rpm-gpg/GPG-KEY-ssp
Answered by Jason Fitzpatrick on November 7, 2021
I had the same issue with a P408i-a and an older version of ssacli (ssacli-2.60-19.0). I was able to resolve it by using a newer version of ssacli (ssacli-4.17-6.0).
Answered by m1tttt4 on November 7, 2021
Get help from others!
Recent Answers
Recent Questions
© 2024 TransWikia.com. All rights reserved. Sites we Love: PCI Database, UKBizDB, Menu Kuliner, Sharing RPP