raspi-config network option not working

Had the same problem after installing OMV5 with raspbian desktop version. I then uninstalled OMV5 but this problem arised...

The problem in my case, had to do with dhcpcd service being missing, not being able to get an IP. You can check if it is available with the next command.

pi@rpi:~ $ sudo service --status-all
 [ - ]  alsa-utils
 [ - ]  anacron
 [ - ]  apparmor
 [ + ]  avahi-daemon
 [ + ]  bluetooth
 [ - ]  cgroupfs-mount
 [ - ]  console-setup.sh
 [ + ]  cron
 [ + ]  cups
 [ + ]  cups-browsed
 [ + ]  dbus
 [ + ]  dhcpcd
 [ + ]  docker
 [ + ]  dphys-swapfile
 [ + ]  fake-hwclock
 [ - ]  fio
 [ - ]  hwclock.sh
 [ - ]  keyboard-setup.sh
 [ + ]  kmod
 [ + ]  lightdm
 [ - ]  mdadm
 [ - ]  mdadm-waitidle
 [ + ]  monit
 [ + ]  networking
 [ - ]  nfs-common
 [ + ]  nginx
 [ - ]  paxctld
 [ - ]  plymouth
 [ - ]  plymouth-log
 [ - ]  postfix
 [ - ]  pppd-dns
 [ + ]  procps
 [ - ]  quota
 [ - ]  quotarpc
 [ + ]  raspi-config
 [ ? ]  rng-tools
 [ - ]  rpcbind
 [ - ]  rsync
 [ + ]  rsyslog
 [ - ]  saned
 [ + ]  ssh
 [ - ]  sudo
 [ + ]  triggerhappy
 [ + ]  udev
 [ - ]  udhcpd
 [ + ]  watchdog
 [ - ]  wd_keepalive
 [ - ]  x11-common
 [ + ]  zerotier-one

Then, I configured my raspberry with a static IP to have network connectivity. Assuming you are using WIFI interface and you have a valid confguration on /etc/wpa_supplicant/wpa_supplicant.con:

sudo wpa_supplicant -c/etc/wpa_supplicant/wpa_supplicant.conf -d -iwlan0
sudo ifconfig wlan0 192.168.1.143 netmask 255.255.255.0
sudo route add default gw 192.168.1.1 wlan0
sudo echo nameserver 8.8.8.8 > /etc/resolv.conf

You can also use eth0 interface and skip wpa_supplicant step.

And finally, I installed dhcpcd

sudo apt-get install dhcpcd5

After I reboot the rpi, Wifi manager plugin and raspi-config worked again.

Check also these links:

https://stevessmarthomeguide.com/configuring-networking-raspberry-pi/ How do I set up networking/WiFi/static IP address on Raspbian/Raspberry Pi OS? https://www.raspberrypi.org/documentation/configuration/wireless/wireless-cli.md https://www.howtogeek.com/118337/stupid-geek-tricks-change-your-ip-address-from-the-command-line-in-linux/

Try run wpa_supplicant interactively:

sudo killall wpa_supplicant
sudo wpa_supplicant -c /etc/wpa_supplicant/wpa_supplicant.conf -d -iwlan0

This will provide a lot of diagnostic logging; in my case (using a USB Wifi dongle), "Driver does not support authentication/association or connect commands". Once I downloaded the off-kernel driver, wpa_supplicant worked fine and so did raspi-config's N2 configuration.

Reference: https://unix.stackexchange.com/questions/400101/how-to-get-the-wifi-working-with-r8188eu-driver-on-my-raspberry-pi

You are using a Raspberry Pi 2B. This model does not have an on-board WiFi device so it does not make sense to enable WiFi with raspi-config. It seems this results in the error message you reported.

Question

How to use Raspbian version 2019 April to config WiFi for Rpi 2B?

Answer

Introduction

The OP has a Rpi2B with a WiFi dongle. He has a problem configing Wifi. This answer has two parts:

1. Install Raspbian on 3B+ and config Wifi.

2. Use the same SD card to config the 2B.

Setting up Rpi2B with a Wifi Dongle

Preparing a micro SD card with Raspbian stretch 2018apr image for Rpi2B and Wifi Dongle

Checking out if Rpi2B Raspbian stretch 2019apr can detect TP-LINK TL-WN727N

I found the setup can detect the TP-LINK Wifi dongle. I remember I needed to google a list of dongles that Rpi can detect. So I would suggest you to check that out by the command lsusb. If you can detect the dongle, then you are almost there! :)

Entering Wifi SSID and password at desktop

setting up Wifi in desktop is even easier. The steps are listed below.

1. Select your Wifi country (otherwise top right network icon won't work).

2. At top right corner, click the double red cross icon (Wifi and Ethernet).

3. Select to turn on your network in the list (my network name is tlfong01).

4. Enter password (pre shared key).

That is all.

Good luck.

/ to continue, ...

---

The paragraphs below are out of date and need to be modified and/or deleted, after I have completed the answer above.

---

Let me see.

I am using Rpi3B+ and Raspbian 2019apr.

When you are configuring WiFi under terminal mode, you should have gone through the last couple of steps as shown below:

You must enter the correct ssid and passphrase, otherwise you will get the N2 Wi-fi error message.

The "ssid" and "passphrase" should be the same for your other WiFi devices, such as your mobile phone. You might like to try your ssid and passphrase with your mobile phone first, to make sure they are OK.

And perhaps you forgot to switch on your router? :)