Motor Vehicle Maintenance & Repair Asked on August 17, 2020
I have changed the oil a couple of days ago, and I’ve noticed that the low oil pressure light stays on longer than normal. Normally, it goes out almost immediately (<1s) after starting the engine, while it sometimes takes up to 4 seconds now after the oil change. This only happens during a ‘cold start’, not when the oil is already warmed up (then it goes out immediately).
The oil level is fine and stable, there are no leaks, and the oil is a high quality 5w30 oil that is specifically recommended for the car; the oil viscosity is identical or nearly identical, I believe, to the previous oil (it was either 5w30 or 5w40). The oil filter I used was a high quality Bosch filter. The car works perfectly. Again; this only happens during a cold start; never during a ‘warm start’ when the engine oil is already warmed up, nor during driving.
I don’t think it’s a big deal, but I would like to understand why this is happening. I pretty much rule out a malfunctioning oil pressure sensor, since it only started happening after the oil change. Oil viscosity also seems to be okay, oil levels are fine, the oil and filter quality are both okay,…
I’ve thought about the clean oil being thinner than the dirty oil causing this rather subtle issue, but I have no idea whether this is true, let alone whether this can cause such a warning.
It sounds like you are getting drain back. When your engine sits without running for a period of time, most all of the oil in the oil passages drains back into the crank case. When you restart your engine, the oil has to be brought from the pan back up into the oil passages, then you see your oil pressure raise. Since I don't know which year your BMW is, I cannot tell you if there is an oil filter for your car which has an anti-drain back feature. If so, this will ensure oil stays in the oil passages and you'll see oil pressure right off the bat, or at least within the second you are accustomed to. If you recent changed which type of filter you use, you may want to go back to that style/brand of filter (unless that filter is a Fram filter --- plenty of stuff out there on it, but here is a good example with pictures of exactly what I'm talking about).
Correct answer by Pᴀᴜʟsᴛᴇʀ2 on August 17, 2020
It's also possible that your old oil had built up sludge in your oil galleries - more likely if that oil was based on castor oil - and the new oil dissolved a bunch of that sludge out, making the oil galleries effectively much larger.
Answered by TDHofstetter on August 17, 2020
I've had this problem twice in my 2001 325CIC (E46) and both times it was the oil sensor going bad.
Answered by Chris Markle on August 17, 2020
Yes I know this question was asked over a year ago. Whatever. First there is no drain back valve on the n42 oil filter element and you cannot fit it "upside down". It can be fitted either way.If this oil light delay definitely occurred strait after the oil & filter change, and you did NOTHING else, then the answer will lie in either of these i.e. the oil is thicker than the previous oil or the filter had a higher flow resistance than before. Somehow you have introduced a flow resistance that wasn't there earlier and the oil is taking a second or so longer to get from the pump to the bearings to build up pressure to operate the sensor. It would be a coincidence that the sensor failed exactly when you did the oil change.
Answered by Phil on August 17, 2020
I've had the same problem with my 318 m43 after an oil change which lead me to remove the oil filter housing to check the drain back valve as I was sure this was the cause, it wasn't. What I did find, having worked out how the oil is circulated, is that the anti return valve only shuts off the return of oil held within the engine when it is switched off. In fact there are 4 valves in total. One, as already mentioned, a further 2 in the filter housing and a 4th at the pump. The 2 within the filter bowl are at the base of the bowl. One allows oil into the filter bowl from the pump and the second one allows oil into the secondary oil gallery past the oil pressure switch and into the feed line to the engine. Both of these valves are a one way design and need to be checked. If they are faulty the housing needs to replaced. Now the 4th valve and the one that caused my problem. On the m43 engine the oil pump is mounted within the timing chain case with a pick up pipe that draws oil up from the sump into the pump and then up into the filter bowl via the one way valve. However, there is a pressure control valve to the side of the pump which also holds oil in the pump when the engine is switched off. If this valve is weak or leaking the pump runs dry and when the engine is next started oil needs to be drawn from the sump up the feed pipe into the pump then pressure is created and pushed up the feed line to the filter bowl past the 2nd valve into the filter and only then does the retained oil in the filter get forced onward to the 4th valve in the block and onto lubricate the engine. If the valve next to the pump held oil at the pump it would remain primed and oil pressure and circulation would be almost instantaneous. If the valve is leaking back this is where the problem lies with the delay in obtaining pressure.
I've replaced my pressure control valve, seal and spring and my light goes almost before the engine has the chance to fire while cranking.
I hope this helps and good luck.
Answered by Gary on August 17, 2020
Get help from others!
Recent Questions
Recent Answers
© 2024 TransWikia.com. All rights reserved. Sites we Love: PCI Database, UKBizDB, Menu Kuliner, Sharing RPP