Is straight lumber a thing of the past?

The problem with today’s lumber it comes off much smaller trees and unless #2 or better kiln dried it can look like what you are finding.

Today to get what you have you basically have to purchase vertical grain lumber (way expensive).

Sometimes it gets mixed in the sorter but you have do dig through a unit to find it if the mill does both like mine.

In any case to find premium pieces today you have to purchase vertical grain or buy kiln dried it is usually straight and dry but dig to find the best pieces.

You can find “straight grain” lumber, but most people don’t know how to order it and most “yards” (Home Depot, etc.) won’t order a small amount (half units, etc.).

Lumber is divided into three “Grades”: boards, dimensional, and timber. Further, dimensional and timbers are graded into “light framing”, decking, beams, timbers, etc. Those grades are further graded into: standard, select, utility, economy, No. 2 & better, No. 1 , etc.

For “Boards”, it’s further graded into “appearance grades”, they are further graded into: finish grades, casing, flooring, siding, etc.

Lumber yards keep a standard grade for framing and a standard grade for trim, etc.

In order to get the material you want, you’ll need to special order the size and grade. (Remember, lumber grading rules allows 10% mis-graded boards in a unit and it’s still considered acceptable. I’d order 10% - 20% more than needed if the appearance grade is critical.)

Without 'fixing the system' haha, one approach you can use to try and mitigate the worst of it, at your local Hope Depot, lay the boards down on the store floor, on all sides and see which ones are the straightest.

It doesn't completely fix the problem but it does help mitigate and reduce the worst of it.

It helps if they've just refilled the wood of course and you get one of the first chances to do this. You'll notice that others already do this so when there are only a few planks left... they are often really crappy.

Home Depots wood is the worst. I live in Northern California and use Freedman's out here. Use smaller retailers with lumber yards and you will have much better success. Also it helps to look down the slim side of the board like you look down a rifle barrel (one eye closed) to see if the board is straight. I get straight wood every trip to the store, but like I said, I don't go to HomeDepot.

Yes, the "HD Prime" stuff is usually quite terrible. Even if you find a straight piece you better use it that same day or else it will warp and bow by the end of the week.

My Home Depot sells premium Burrill brand lumber. For me, 9 out of 10 boards at the store are straight and will stay straight for weeks. HD Prime is more like a 2/10 and I've never had one stay straight in storage.

If you have a table saw then buy a 2x6 and rip it into two 2x3 boards.

My preference is Lowes over HD, but I'd assume they're basically the same.

When I go to get lumber, I bring gloves because I know I'll be moving a lot of wood to get something decent. I'd guess that on average I only take about 50% of the boards, sheet or dimensional, that I pick up to look at.

That said, we built a shed last summer and, due to the quantity of lumber necessary, we simply ordered online and paid the $50 to have it delivered. We ordered about 20% more than we needed figuring that would give us a good start on what we needed and we'd go return the bent pieces as "oops, got more than we needed", then pick through the piles for straight lumber to replace it. Out of all the dimensional and sheet goods, we had one 2x4x16' and one 4x8x3/4 pressure treated plywood that were warped beyond use. We had a few that were bent or twisted, but that we were able to get straight shorter pieces (mostly for the gambrel roof trusses) out of them.

I've still got a reasonable stock of lumber from that purchasing experience, and the next time I need to purchase lumber (once prices drop from the stratosphere due to the fear virus), I'll strongly consider buying a stockpile again.

So my question is, do they still produce 2x3" studs that are straight?

Yes. The better question is - Who is "they"? Straight lumber is plentiful and cheap in Canada, for example.

It's important to understand that pricing and availability of quality lumber in the United States has long followed the ups and downs of the Canada/US Softwood Lumber Dispute, which has been going on since 1982.

Most recently, this dispute was inflamed as a part of former US President Trump's policies of economic protectionism. As such, since 2018 there has been a significant increase in the cost of lumber and a decrease in the availability of quality lumber as builders fight amongst themselves for the best of available domestic inventories while quality imports remain heavily taxed and expensive, driving up prices and reducing supply. The NAHB estimates that this is adding up to $9k to the price of new homes.

Sometimes the world of politics can feel abstract and distant, but this is one example where political sabre-rattling has real consequences - namely, sad faces in US lumber aisles.

Other factors are also compounding the issue at the moment, including the impact of recent wildfires in the Western US that destroyed thousands of acres of lumber forest.