Home Improvement Asked on August 14, 2020
I have four 355W solar panels and three 315W solar panels. I have a 40-amp mppt and a 30-amp mppt charge controller with 100V Max PV voltage.
The distance solar panels to charge controllers is around 15 meters and the distance battery to charge controllers around 1.5 meters.
My battery bank system is 24 volt. The solar panel voltage is around 37 volts. They are not connected yet.
Out of the three 315W solar panels, one is pointed south, the other 2 east. he one pointed south is shaded until 9 AM. They are at 16 degree angle. The other four 355W are not yet installed.
The system is in the Caribbean.
I have 8 6-volt batteries in 2 parallel strings.
I need help with the wiring of the solar panels (series or parallel) and also the wire gauge.
Thank you in advance for your help!
The specs for the 315W solar panel are:
Pmax = 315 W
Max voltage = 37.4 V
Max current = 8.42 A
Open Circuit voltage = 45.5 V
Short circuit current = 9.12 A
Power tolerance = 0~+6w
The maximum fuse rating = 15 A
The specs for the 355W solar panel are:
Rating power at stc(Wp) = 355 w
Rating power voltage(Vm) = 37.58 V
Rating power current(Im) = 9.45 A
Open circuit voltage (Voc) = 46.26 V
Short circuit current(Isc) = 9.85 A
Your panels are 37V yet your controller is 100V max. Since 3 panels is 111V, that means we can only wire 2 panels in series. That also means odd panels will be a problem.
But so far, the odd panel already is, since it has a different facing than the other panels.
The mixed panels are so close in working voltage that they can be paralleled without worry. However that will necessitate fat cables.
To work them in series, will require they be facing the same direction and recieve sun at about the same times. If they are in series, and one is in sun and the other in shade, you will not get much out of that array - whereas if they were in parallel, you would at least have the sun-lit one. However parallel requires fat cable.
So for right now, the two 315W solar panels that face the same way can be placed in series and wired to one of the controllers. The voltage drop calculator says #12 wire will be fine for this purpose with only 2.11% voltage drop. The single 315W panel facing oddly should go on the other controller. This can use #12 but will have 4.22% drop; #10 wire brings this voltage drop into line at 2.55% drop.
When you add the other 4 panels, again the question will be if they can be grouped in pairs, with each member of the pair facing the same way and going in/out of shade at about the same time. If so, they can be placed in series.
Multiple pairs of series-wired panels can then be paralleled together for the cable run back to the panel. Two panel pairs should use #12 for 4.22% drop, or #10 wire for 2.55% voltage drop. Three panel pairs could use #10 wire for 3.83% drop, or #8 wire for 2.52% drop. Or, each panel pair could use its own #12 cable going back to the controller. Your call.
Individual panels should each get their own home-run, as it will not be economical on wire to try to parallel them. Use #12 with 4.22% drop, or #10 for 2.55% drop.
The series pairs of panels should be paralleled onto the larger charge controller. The individual panel(s) should be paralleled onto the smaller one, but no more than 3 panels onto this 30A unit.
Correct answer by Harper - Reinstate Monica on August 14, 2020
Get help from others!
Recent Questions
Recent Answers
© 2024 TransWikia.com. All rights reserved. Sites we Love: PCI Database, UKBizDB, Menu Kuliner, Sharing RPP