If you have the condensers already selected, you should be able to get the two pieces of data you need to make a decision.

1) price increase for 3 phase condenser
2) operating power for single phase and 3 phase units.

I suspect they will quote you that the two units consume the same amount of operating power.

Yes, theory says 3 phase motors run smoother just like V8s run smoother than 4 cylinder engines. But the practical difference in motor life is something you will probably never see.

One possible reason that a 5 ton unit is available in 3 phase is that the amperage is lower and thus you could save some money on the wiring cost. This comes at the cost of an extra circuit breaker.

Single phase

1hp = 756 watts

5hp = 3730 watts

3730 watts at 230 volts = 17 amps

Three Phase

3730 watts = 3730(watts) / (207(v) x 1.73) or 3730 / 358.11 = 10.4 amps.

Three phase is 40% less amperage.

There are other things to make this accurate, like motor efficiency and power factor. I used 1 for each.

Another savings is that with the reduced amperage you can reduce your conductor size for your feeder. With the price of copper today that could help matters too.

I used 5hp for no special reason, just a nice round number.

I suggest using three phase.

Formula found here.

The above example of 5hp at 240v = 3730 watts and 5hp at 207v three phase = 3730 watts is correct. You draw less amperage with three phase but with more added voltage. Power is power and you draw 3730 watts with either scenario. Your savings will come in the durability and longer life of a 3 phase motor. You will also reduce your feed supply conductor size but will have to add another pole to your breaker or disconnect switch and one more conductor too! By using a three phase motor you will also balance your load on your service and probably increase your power factor efficiency which your hydro utility probably charges you extra based on a lower one, (check your bill). The nod goes to three phase but only slightly. Pay hundreds more for a 3 phase not thousands.

Volts x Amperage=Wattage I have a 220 volt device (motor, dryer whatever... it makes little difference for this example). Single phase device draws 43 amps (43 x 220 = ~ 9460 Watts or 9.5 KW) Same unit with 3 phase draws 25 amps (25 x 220 =~ 5500 Watts or 5.5 KW) *** The same amount of work is output with either unit despite the 3 phase using less power because it is more efficient.

I currently pay $0.14 / KW and Run the unit 6 hours a day. Single phase costs me (9.5 x .14 x 6) per day to operate or ($6.65). Three phase costs me (5.5 x .14 x 6) per day to operate or ($4.62) a difference of $2.03/day. Therefore the difference in 1 year (5 days a week) is a yearly savings of $527.80.

208/120Y is cheaper for supplying condominiums because one neutral can carry the unbalanced loads of three ungrounded conductors. But for the consumer, the voltages difference of 208V vs 240V usually equates to the same overall wattage, with the only negligible concern being it takes longer for heating elements to reach their desired temperature. As for motors, whether or not they're more efficient is not a question, but rather if you'd notice that difference in your monthly power bill. That I would probably say no just because being a residential area.

Three phase with current=1, current vector sum is 1.5. Single phase motor, I suppose it is two phase driven, with 4 poles and 90 degrees pole pitch, to generate a vector sum of 1.5, the phase current must be 1.5, 2-phase power consumption=1.5*1.5*4 (4 windings) = 9, 3-phase = 1*1*6 (6 windings) = 6, So 2 phase motor consumes 9/6=1.5 times more power than a 3-phase motor with the same torque output.

Honestly I think there is no meaningful power savings to be had merely because a 5 ton condenser uses three phase vs single phase. Ditto on reliability. A three phase 5 ton compressor is only marginally more reliable than a single phase hermetic unit that size. The issue with the single phase units is that compressor run capacitors do go bad every 10 years or so; but they are cheap and easy to replace.

I have maintained 3 phase 3-5 ton condensers that were installed because it was felt they were more reliable than single phase. Issues like correct installation, EER rating (not to be confused with SEER rating), and correct maintenance unrelated to the compressor drowned out any concerns about the type of power supplied.

5 ton units are sold in both single and three phase configurations because in some commercial environments three phase power is easier to come by than single phase power.

I live in a three phase power area here in Central Phoenix. My 3 phase 5 ton unit is 19 years old. My Home is 2500 ft sq. In all these years for an August power bill I have NEVER paid more than $100 in a monthly power bill. My neighbors who were advised by so called...technicians...to replace their 3 phase units with single phase are paying August power bills of $300-450.

It is your wallet; what are you willing to pay year after year after year

This is a really simple answer:

1) Power draw is amps * voltage/efficiency. A motor needs a certain amount of power no matter what. You pay by power consumed. So, your bill will be virtually identical because power doesn't change. The only reason it isn't perfectly identical is efficiency:

2) Three phase spreads the load over 3 wires instead of two, reducing current (amps) by 50%. Amperage is what causes heat which causes increased resistance which causes more amperage drawn to make up for it (lowering efficiency). So by reducing amperage, you increase efficiency, lowering power draw. Therefore the amp difference isn't quite 50%; it might be 51 or 52%. The decrease in power is very minimal. A couple percentage points that will get overshadowed by environmental effects.

The bigger points to consider are the cost differences of installing 3 phase vs single phase and cost to wire those, and the total amperage your panel is rated for. If you need fewer amps to fit in the panel and the cost to install isn't significantly higher, go with three phase. If you have three phase and the cost is similar, always go three phase. But there's virtually no lower cost to run by doing it.