Where to mount a headlight if the handlebar is obscured by a basket

Helmet lights are good. Usually in addition to one on the handlebars.

The pro of the helmet light is that you can light up things that are not directly infront of you. The pro of having an additional light is that it increases the chance of being seen and adds extra illumination for you.

The con is that if you are looking to the side and a car is coming from the front they will not see the light shining at them, so you should not have a helmet light as your only light.

The obvious places are on the basket, on the fork crown, or on the fork itself, although they may require mounting hardware or a different light altogether. Reading this may get you some ideas. Looking at the Reelight line-up may also spark your imagination.

Or you could also go with unconventional solutions like Revolights.

There are various extension mounts you can buy or build to reposition lights and other handlebar-mount items. I have a purchased unit that can be adjusted maybe 2" higher than the bar, and which can mount on either the bar or the stem. You can also craft something with a short piece of plastic pipe, a few screws and brackets, and some cleverness.

Lucky's solution can be done with any sort of short, black tubular thing. E.g. an old film canister, or a stub of wood or dowel. Use some cheap wire snips to open up the mesh to accommodate the light-mount's adjustable strap about 1/2 inch below the top-front edge, and wrap the strap around the black object and the basket (through hole and over the edge). Cinch it tight and you'd have as much rattling as you would have from attaching to the handlebars in the first place. You could even use some rubber from a used tube or other bike-reflector/light clamps and put it between the block and the basket.

               [Basket below]

                       =====<    [light, on "O" tube]
                      /--
                |     ||O|
[Bike here,     |     --/
 forward        |      |
 is to the      |      |
 right]         |      |
                --------

Another idea is to get a small (3-4 inch) piece of flat metal bar, e.g. a metal bracket with holes (pref. aluminum, plastic). At the bottom of your basket, either on side near front or even straight forward, use wire snips to make a little horizontal slit for the bar to go through, but so it can stay flat with the bottom of the basket. Now you lay the bar there with half in, half out, tied to the bottom with black zip ties or a nut and bolt. You could zip tie the light to the bar itself or maybe screw a piece of wood dowel or pipe to the end and attach the light to that.

               [Basket below]

                |      |
[Bike here,     |      |
 forward        |      |           [light, at end of bar, maybe with a tube.]
 is to the      |      |  =====<
 right]         |    ______O
                --------

Depending on how you can recharge the light, and on whether you mind reaching in to press the power button, you could even snip a big enough hole in the front of the basket so the light would simply lie flat (adjusted for angle) on the bottom of the basket, inside, with only the lens up against the outside. This could use black zip ties and be very discrete.

               [Basket below]

                |      |
[Bike here,     |      |
 forward        |      |
 is to the      |      |           [light, strapped inside]
 right]         | =====<
                --------

Zip tie the light to the side of your basket. May take several tries to get the angle right and will not work on all baskets. This has allowed me to still be able to reach the light while riding.

Something like this accessory is what you need:

Can be fitted onto wired or meshed bicycle baskets. This specific model is made by the "Rixen & Kaul" and can be found in many online shops. E.g. Amazon - Rixen & Kaul Light-Clip Basket Fitting - Black.

Attach a pipe or pole to the basket and hey presto! Another "handlebar"!

Photos from Bike Hacks contributors:

ELECTRA LED BASKET FRONT LIGHT

There is still no solution.

[1] The KLICKfix accessories do not work. They look good, but the lamp vibrates as you ride, causing stress where the KLICKfix meets the basket and eventually the vibration causes it to cut through your wire basket. I've had two wire baskets damaged like this.

[2] The Electra LED lights are too feeble.

[3] Attaching a pipe with PVC is a pretty clunky solution.

What's needed is a mount which could attach to the bottom of the basket, either above the bottom, or under it. The problem is that each lamp manufacturer's mount is different, so if Smart (e.g.) designed a mount to attach to the base of wire baskets, it would only fit Smart lights. So it would be uneconomic to manufacture.

I don't know what the answer is.

Not sure what the legal requirements are for a light for you, but if its a be-seen light (as opposed to a see-the-road light) then Electroluminescent wire is great at showing where you are. Also known as "EL Wire" this stuff is like a light plastic rope, that can be woven or flexed.

Connect it to a suitable power source, and it will glow in whatever colour you chose. Some are 3V, some USB/5V, and some are 12V. I've run a 12V one on 18V and it worked fine, but no idea how that would impact longevity.

Not the best photo, but you can see the blue line around the front of the basket. EL wire can be held on the outside with a series of white cableties / slip ties which won't block the light. And the battery can be put inside the basket. Additionally, little of the light will be visible to the rider and so won't reduce night-vision.

Downsides

• This does not illuminate your surroundings more than perhaps half a metre, and only in a general way. There is minimal "throw" so if you want to light up the road, you're back to square one
• Some people can hear these things - they use a high frequency AC waveform to excite the wire, and it sounds like a mosquito repellent. Which might also be an advantage.

You can get many different colours, and they're generally waterproof enough. The power connector would be the weakest point, into a USB battery bank/power bank.