3D Printing Asked by Blubberguy22 on January 11, 2021
I just installed my (v3) BLTouch with a vanilla version of Marlin (1.1.9) on my Ender 3 and everything seems to work fine (including auto home) except the probing. It repeatedly does the first three probes (successfully) but then tries the fourth and fails. Even when disabling the axis movement (X/Y stepper motors) the issue persists, which would indicate that it is not a bad connection or physical location dependent. Any ideas on how to troubleshoot?
On second thoughts, it seems that it now fails inconsistently, so it is probably a wiring issue, although there is still the issue of it not retracting before printing and not leveling well when it does (although those issues would be more appropriate for a separate question), among other things.
<Edit: Resolved, I both replaced the BLTouch and updated my firmware, but I believe it was the latter that fixed it.>
Is your BL Touch a v3 (likely if you've only just purchased it)? If so, make sure you're using the bugfix version of Marlin 1.1.9, which supposedly fixes the compatibility issues. I say supposedly because there's also a capacitor on the mainboard that can be removed to fix the issue, and once I removed it (and commented out the specific v3 bits in the firmware) the BLTouch performed noticeably better than when relying on the bugfix firmware alone.
Teaching Tech on YouTube has a few BLtouch Ender 3 videos, covering the changes for configuring the bugfix firmware and the removal of the capacitor.
Correct answer by StringsOnFire on January 11, 2021
Just leaving this note here as I have had my own BLTouch issues, maybe it will help someone else...
V4.2.2 board on an Ender 3. BLTouch V3
I was getting inconsistent failures on both home and bed level, also would drive into the bed on occasions.
I would first recommend keeping your Z stop switch connected (the BLTouch uses the five pin header on the V4 boards, not the Z stop.
I tried with extension cable and connectors, then hard wired the extension cable, also removed the pin header plastic body on the connector going into the board (as it's not the right type, and sits a bit too high) to make the cable ensure good connection to V4 board.
Correctly levelled bed, Z stop, was getting awesome prints with stock Creality firmware for Ender 3 Pro and BLTouch on v4.2.2 board (without adaptor board version).
Still random crashes into the bed and random bed level fails.
I'm racking my brains, replaced nearly all wiring, made sure good connections, changed to Marlin 2.X.X bugfix (which you load onto SD and turn the machine on).
Still random crashes into the bed and bed level fails.
So I'm now getting close to, this has to be a faulty touch surely, I've done my fair share of electronics repair being an electronics engineer by trade.
I'm looking at the touch, I see a solonoid, I checked how it works, the ferrite core looks flush with the top of the touch housing. I turn it a full turn into the touch. I'm getting less errors.
I think I finally ended up turning it about 0.5 mm to a 1 mm into the housing. All seems much better. No fails or crashes since the last tweak of the ferrite grub screw.
If the sensor is a little off on the Ender, and I hear they are, then maybe the position of the ferrite is more sensitive on these machines. That will affect the magnetic flux of the sensor.
I also found a link brief on the V3 probes and there is a section that points out a 0.3 mm gap from top of ferrite to top of probe stated, mine was flush.
I have ordered another just to be on the safe side but I think this may have helped stop my random fails.
Answered by Paul Smith on January 11, 2021
I've been through the same sort of issues and eventually found that it was attributed by the cable and connector. Re-check or re-wire the sensor, this helped me out.
Answered by 0scar on January 11, 2021
Get help from others!
Recent Answers
Recent Questions
© 2024 TransWikia.com. All rights reserved. Sites we Love: PCI Database, UKBizDB, Menu Kuliner, Sharing RPP